Hanna-instruments HI 121 Bedienungsanleitung Seite 33
- Seite / 60
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
33
When in normal measurement mode:
• If only “AL.LO” item is set, the instrument will beep when the reading
is below alarm low value.
• If only “AL.HI” item is set, the instrument will beep when the reading
is above alarm high value.
• If both alarms are set, the instrument will beep when the reading is above
alarm high value or below alarm low value.
Note: If “AL.HI” item is less than or equal to “AL.LO” item, “WRONG” tag
will blink.
AutoLOG SETUP
AutoLOG Start Condition
• Select the “Strt” item. The displayed AutoLOG start condition will be the
previous set one. The default value is “btn” – button (start with key).
• Press and keep hold down MODE while in view mode, when time is
displayed, to view the set date.
• If pressing CAL while in view mode, the start time will be displayed.
Notes: • Pressing CLR or 2nd then CLR while in changing mode, the
start condition will be set to default (“btn”).
• The first displayed value after “btn” will be the current time/date.
AutoLOG End Condition
• Select the “End” item. The displayed AutoLOG end condition will be the
previous set one. One of the following options will be available: “dur”
(duration), “SAMP” (samples number), “rdG” (reading limits).
• Pressing MODE while in view mode, the instrument will display one of the
options: “dur”, “SAMP”, “rdG” & “pH”, “rdG” & “mV”, “rdG” & “Rel mV”.
• Pressing CAL, the instrument will enter in changing mode in according
with the selected option and will display one of the following messages:
• “dur” on the secondary LCD and duration (hh:mm) on the primary
LCD, along with “TIME” tag. The default value is 3 hours. The
duration can be set from 1 minute to 199 hours and 59 minutes.
Note: Pressing CLR or 2nd then CLR while in changing mode, the
end condition value will be set to default (3 hours).
• “SAMP” on the secondary LCD and sample number on the primary
LCD. The default value is 1000 samples.
Note: Pressing CLR or 2nd then CLR while in changing mode, the
end condition value will be set to default (1000 samples).
• “rdG” on the secondary LCD and last set limit value on the primary
LCD, with the corresponding range tag blinking. The default value
is 7.00 pH or 0.0 mV, in according with the selected range.
Notes: • Pressing MODE while in view mode, another resolution
is selected.
• Pressing CLR or 2nd then CLR while in changing mode, the
end condition will be set to default (7.00 pH or 0.0 mV).
- HI 121 & HI 123 1
- WARRANTY 2
- TABLE OF CONTENTS 2
- PRELIMINARY EXAMINATION 3
- GENERAL DESCRIPTION 3
- FUNCTIONAL DESCRIPTION 4
- Calibration Check 5
- NUMResolutionISE 6
- RelmVmVpH 6
- SETGLPAutoHOLD 6
- PaperPrintAutoHOLD 8
- HI 121 AND HI 123 10
- SPECIFICATIONS 10
- OPERATIONAL GUIDE 11
- ERROR MESSAGES 20
- WARNING MESSAGES 20
- ENHANCED CALIBRATION MESSAGES 20
- ELECTRODE CONDITION & 21
- ELECTRODE RESPONSE TIME 21
- RELATIVE mV CALIBRATION 22
- ISE CALIBRATION 23
- TEMPERATURE CALIBRATION 36
- Lot (or record) number 37
- AutoHOLD 38
- PRINTING (HI 123 only) 39
- Slope 99.7% 41
- • For AutoLOG mode: 42
- PC INTERFACE 45
- DEPENDENCE 48
- ELECTRODE CONDITIONING 49
- & MAINTENANCE 49
- PRINTER MAINTENANCE 52
- (HI 123 only) 52
- TROUBLESHOOTING GUIDE 53
- TROUBLESHOOTING GUIDE (cont.) 54
- TEMPERATURE CORRELATION 55
- FOR pH SENSITIVE GLASS 55
- ACCESSORIES 56
Verwandte Produkte und Handbücher für Messgeräte Hanna-instruments HI 121
(56 Seiten)Wilbur-curtis WB-14-11 manuali
Manuali dei proprietari e guide per l'utente per Bollitori per acqua Wilbur-curtis WB-14-11.
We fornisce 1 manuali pdf Wilbur-curtis WB-14-11 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern